Our Website Use Cookies

By continuing to use this site you are agreeing to cookies being placed on your computer. To find out more about the cookies, see our Privacy Policy.

NOTICE

Due To COVID-19, we cannot guarantee next day delivery. Though we endeavor to do our best but delays may happen due to delays with courier services.

EnGenius ENS500EXT-AC - 5GHz AC867 Wave2 11ac Outdoor Wireless Access Point

Back Order EnGenius ENS500EXT-AC - 5GHz AC867 Wave2 11ac Outdoor Wireless Access Point

The EnGenius ENS500EXT-AC is an 802.11ac long range outdoor wireless access point that you can use for any bandwidth and speed demanding applications like HD video streaming or IP-based surveillance system. It is Capable of up to 867Mbps speed under the 5GHz frequency band. It has detachable antennas, which you can switch to a more robust and higher gain antenna system like the Poynting directional or omnidirectional Wi-Fi antennas.

Features

  • Up to 867Mbps 5GHz speed performance
  • 2x2 802.11ac Wave2 (MU-MIMO) equipped.
  • Inbuilt high gain directional antenna 14dBi antena
  • Safe & Robust IP55 enclosure for extremely weather deployment
  • Easy Access Point reset via PoE Adapter (100 meters or 328 feet)
  • Equipped with 802.11ac Wave2 engine to enhance overall bandwidth/speed
  • Send/Receive Multiple HD quality IP surveillance content over wireless transmission
  • Easy monitoring & device configuration on smartphone/tablet, thanks to EnGenius’ “EnWiFi” device management system

Deployment Scenarios

Below are few scenarios/applications where you can use the ENS500EXT-AC or the ENS500-AC in your outdoor wireless distribution projects.

  • Shopping Malls
  • Building Sites
  • College Campuses
  • Stadiums & Arena
  • Public Lightings
  • Airport Terminals
  • Resort Properties
  • Construction Sites
  • Hospital Buildings
  • SmartHomes Project
  • Parks & Campgrounds
  • Warehouse Operations
  • and more

ENS500EXT-AC Technical Specification

The ENS500EXT-AC is an outdoor 5GHz 11ac Wave2 Wireless Access Point, which you can use to share your existing Internet connectio, whether for free or paid. You can use it in captive portal or hotspot application. See full product technical specification below.

Wireless Radio Specification
Access Point Type Outdoor, IP55, dual radios concurrent, 5GHz 802.11 ac, 2x2 MIMO is backwards compatible with 802.11 ac/a/n mode
SU-MIMO Two (2) spatial stream SU-MIMO for up to 867 Mbps wireless data rate to a single wireless client device
MU-MIMO Two (2) spatial stream MU-MIMO for up to 867 Mbps wireless data rate to transmit to two (2) wireless client devices simultaneously
Frequency Radios 5GHz: 5150MHz~5250MHz, 5250MHz~5350MHz, 5470~5725MHz, 5725MHz~5850MHz

Support radios and channels will be varied on the configured regulatory domain.
Supported Radio Technology 802.11n/ac:
2x2 MIMO with 2 streams
802.11ac supports very high throughput (VHT) — VHT 20/40/80 MHz
802.11n supports high throughput (HT) — HT 20/40 MHz

802.11n/ac packet aggregation:
AMPDU, ASPDU
Orthogonal frequency-division multiplexing (OFDM) under 802.11ac/a/n
EnJet technology with Time Division Multiple Access (TDMA) under 802.11ac/n
Supported Modulation Type 802.11a/n: BPSK, QPSK, 16-QAM, 64-QAM
802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM
Transmit Power (Maximum Value) 26dBm (Maximum power is limited by regulatory domain)
Tx Beamforming (TxBF) Increasing signal reliability and transmitting distance
Supported Data Rates (Mbps) 802.11a: 6, 9, 12, 18, 24, 36, 48, 54
802.11n: 6.5 to 300 (MCS0 to MCS15)
802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS=1 to 2)
Antenna
Antenna Types Two (2) Detachable 5.0dBi SMA Antennas
Widely frequency supported from 5150MHz to 5925MHz
Interfaces
Networking Interface Two (2) 10/100/1000 BASE-T RJ-45 Ethernet Ports
LED Indicators Display system and wireless transmission status
Reset Button Convert Access Point to the Factory default or the Users Default
Power
Maximum Power Consumption Maximum 8.93W
Power Source Proprietary 24V PoE (Power: 4, 5; Return: 7, 8)
Active Ethernet (Power Over Ethernet, PoE)
Operating Mode
Access Point Mode (AP Mode) Be an Access Point behaves like a central connection for station or clients that support IEEE 802.11 ac/a/n network
Client Bridge Mode (CB Mode) The Access Point essentially acts as a wireless adapter that connects to an access point to allow a system of wireless access to the network in the client bridge mode
WDS Modes (WDS AP, WDS Station) WDS modes uses WDS technology to establish the wireless connection via filling MAC address in both Access Points to enlarge the wireless area
Exquisite RF Management
ACK timeout (Distance Control) Set the ACK timeout to assure the proper distance to deliver wireless signal properly
Site Survey Scan signal level of an environment to provide parameters for performing Auto Transmit power and auto channel
Auto Transmit Power Automatically adjust power level
Auto Channel Automatically assign a clearly channel to perform RF transmission under a pervasive environment
RSSI Threshold Kick client devices that the signal (RSSI) is above the set value from the AP for reducing the interference and optimize the connecting quality
Optimize Performance
Quality of Service Compliance with IEEE 802.11e standard
Prioritizes voice over data for both tagged and untagged traffic
Transmit video, voice and data at the same SSID
Power Save Mode Support U-APSD
Pre-Authentication Compliance with 802.11i & 11x
PMK Caching Compliance with 802.11i - If wireless client devices has authenticated to an access point, it does not perform a full authentication exchange when client devices roaming between access points.
Fast Roaming (802.11r) Use a Fast Transition key to handover between Access Points (ENS500EXT-ACV2)
Multicast to Unicast Conversion Using the IGMP protocol, an access Point delivers high definition content to a large number of clients simultaneously
Management
Multiple SSIDs BSSID support
EnJet Enable: Support 1 SSID for EnJet linkage and 1 SSID for CSMA client to configure EnJet AP
EnJet Disable: Support 8 SSIDs for CSMA client
Guest Network Isolate each client for avoiding an unnecessary touch, leaking sensitive data, and enhancing Internet security and reliability
VLAN Tag Independent VLAN setting can be enable or disable. Any packets that enter the Device without a VLAN tag will have a VLAN tag inserted with a PVID (Ethernet Port VID)
VLAN Pass-through Broadcast VLAN-tag packets to find the destination and deliver packets over the defined path. The functions allows network topology scalable and flexible
VLAN Per SSID Integrate VLAN ID with a SSID interface to forward packets over the defined path. The functions isolate client devices to get more security
VLAN Management Feature is enabled with specified VLAN ID, the device will only allow management access with the same specified VLAN ID from remotely location by using protocols such as telnet, SSH, snmp, syslog etc
Traffic Shaping Controls the bottle of bandwidth to offer the limited bandwidth for an individual SSID or each client per Access Point
MAC Address Filtering Filter up to 32 sets MAC addresses per SSID
E-Mail Alert Provides a network monitoring tool for administrators to stay informed the configuration change
Save Configuration as Users Default Save the customized configuration as default value for different customer demands
Wi-Fi Scheduler Perform a regular reboot on access point at assigned schedule. Perform it to enable or disable 2.4GHz or 5GHz interface from a period time.
SNMP & MIB&CLI v1/v2c/v3 support
MIB I/II, Private MIB
CLI Supported
RADIUS Accounting Help operators to offload 3G to Wi-Fi seamlessly
Wireless Clients list Provide the list to display real status of wireless client devices on this Access Point
Comprehensive Protection
Wireless Encryption Standard WPA2-AES PSK, WPA2 Enterprise
Hide SSID in beacons Supported
Client Isolation Block/Isolate the communication between the associated clients under the same WLAN
HTTPS A secure communication protocol can be enabled to allow secure management web access over a computer network
SSH Tunnel A secure communication protocol can be enabled to allow secure remote shell access or command execution
Mechanical & Environment
Dimensions (Device only) 186mm (L) x 100mm (W) x 29mm (H) (7.54” x 4.49” x 1.88”)
Weight 504g (1.11 lbs)
Operating Environment Temperature: -20°C~60°C (-4°F~140°F)
Humidity: 0%~90% typical
Storage Environment Temperature: -40°C~80°C (-22°F~176°F)
Humidity: 0%~90% typical
Environment Protection Level IP55
Surge Protection Line to Line: 1.0KV
Line to Ground: 2.0KV
ESD Protection Contact: 4KV
Air: 8KV
Mounting
Pole Mounting Assemble a mounting bracket to fix this Access Point on a pole
Wall Mounting Mount this Access Point on a flat wall
Compliance Regulatory
FCC Subpart 15 B
Subpart E 15.407
CE EN 301 893
EN 301 489-1/-17
EN 50385
EN 55032
EN 55024
EN 60950-1/-22
IEC 60529

How & Where to Buy?

To buy the ENS500EXT-AC Long Range Outdoor AP, you can drop by our store located at Novatel Communications, 12 Main St, Buttevant, Co. Cork, P51 K066, Ireland.

To order online, simply click on the Add to Cart button, and then go through the fast, easy and secure checkout process. Payment is provided for your convenience via Authipay Payment Gateway. You can use any supported (MasterCard, Visa, American Express, Diners, etc).

How Will My Order Be Delivered?

Your order(s) will be shipped via express delivery and are normally delivered within 1-4 business days. Your order will be dispatched directly from our warehouse and you will be provided a tracking information for your order, after it is dispatched. If you have any questions on your order status, please contact us.

Write a review

Please login or register to review
  • Brand: EnGenius
  • Product Code: ENS500EXT-AC
  • Availability: Back Order
  • €167.00
  • Ex Tax: €135.77

Tags: 5ghz-long-range-outdoor-ap, wifi-repeater, wif-expander

Loading...