EnGenius EnStationAC - 867Mbps 5GHz 26dBm Outdoor Long Range Point-to-Point Wireless Client Bridge & Access Point






You will need a pair of these units to configure a Point-to-Point System
- Stock: In Stock
- Brand: EnGenius
- Model: EnStationAC
- Weight: 1.11kg
- Dimensions: 32.00cm x 8.60cm x 24.80cm
- EAN: 4713361934636
- MPN: 1102A1254301
NOTE: You will need a pair of these units in order to configure a Point-to-Point Bridge. The EnStationAC is an outdoor 5GHz 802.11ac Wave1 Long-Range Point-to-point Wireless Bridge, that you can use to extend existing Internet connection and share wirelessly. This outdoor device features a MU-MIMO Dual Radio Access Point, that cuts through RF-congested environments within Point-to-Point/MultiPoint applications.
Equipped with a high-gain 19dBi dual-polarized directional antenna, it enables you to setup a faster (up to 867Mbps) and more stable wireless network performance and avoiding the hidden node issue. It lets you extend your network up to 5km without a hitch. Connect two LAN across distance, perfect for Calving IP Cameras, Surveillance System, Internet Connection Sharing, WiFi Hotspot or Captive portal applications.
NOTE: Comes with Factory Supplied EU Plugs
Typical Application Deployment
Our customers, partners, and installers are using this CPE unit in various applications and scenarios, but not limited to:
- SmartHomes
- Building Sites
- Shopping Malls
- Stadiums & Arena
- Public Lightings
- College Campuses
- Resort Properties
- Airport Terminals
- Corporate Campuses
- Hospital Buildings
- Construction Sites
- Parks & Campgrounds
- Warehouse Operations
- Wi-Fi Hotspots Setup
Technical Specification
Wireless Radio Specification | |
---|---|
Access Point Type | Outdoor, IP55, 5GHz 802.11ac 2x2 MIMO is backward compatible with 802.11 a/n mode |
SU-MIMO | Two (2) spatial stream SU-MIMO for up to 867 Mbps wireless data rate to a single wireless client device |
MU-MIMO | Two (2) spatial stream MU-MIMO for up to 867 Mbps wireless data rate to transmit to two(2) wireless client devices simultaneously |
Frequency Radio | 5GHz: 5150MHz~5250MHz, 5250MHz~5350MHz, 5470~5725MHz, 5725MHz~5850MHz |
Supported Radio Technology |
802.11ac/a/g/n: Orthogonal frequency-division multiplexing (OFDM) 802.11n/ac: 2x2 MIMO with 2 streams 802.11ac supports very high throughput (VHT) —VHT 20/40/80 MHz 802.11n supports high throughput (HT) – HT 20/40 MHz 802.11n/ac packet aggregation: AMPDU, ASPDU |
Supported Modulation Type |
802.11a/n: BPSK, QPSK, 16-QAM, 64-QAM 802.11ac: BPSK, QPSK, 16-QAM, 64-QAM, 256-QAM |
Transmit Power (Maximum Value) | 26dBm |
Supported data rates (Mbps) |
802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 300 (MCS0 to MCS15) 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS=1 to 2) |
Power | 23.4W with PSE output |
Maximum Power Consumption | 7.832W without PSE output |
Power Source | 802.3af/at Input; Proprietary 48V-54 V PoE (Power: 4, 5; Return: 7, 8 |
Antenna | |
Antenna Types |
Directional high gain 19dBi antenna Widely frequency supported from 5150MHz to 5925MHz |
Interfaces | |
Networking Interface | Two (2) 10/100/1000 BASE-T RJ-45 Ethernet Ports |
PSE Output | Supply 802.3af power source via the 2nd LAN port. |
LACP | NA |
LED Indicators | Display system and wireless transmission status |
Reset Button | Reverts configuration to the Factory Defaults or the Users Default |
Operating Mode | |
Access Point Mode (AP Mode) | Be an Access Point behaves like a central connection for station or clients that support IEEE 802.11 ac/a/b/g/n network |
Client Bridge Mode (CB Mode) | The Access Point essentially acts as a wireless adapter that connects to an access point to allow a system of wireless access to the network in the client bridge mode |
WDS Modes (WDS AP, WDS BR, WDS Station) | WDS modes uses WDS technology to establish the wireless connection via filling MAC address in both Access Points to enlarge the wireless area |
Exquisite RF Management |
|
ACK timeout (Distance Control) | Set the ACK timeout to assure the proper distance to deliver wireless signal properly |
Site Survey | Scan signal level of an environment to provide parameters for performing Auto Transmit power and auto channe |
Auto Transmit Power | Automatically adjust power leve |
Auto Channel | Automatically assign a clearly channel to perform RF transmission under a pervasive environment |
RSSI Threshold | Kick client devices that the signal (RSSI) is above the set value from the AP for reducing the interference and optimize the connecting quality |
Optimize Performance | |
Quality of Service |
Compliance with IEEE 802.11e standard Prioritizes Voice Over IP data for both tagged and untagged traffic Transmit video, voice and data at the same SSID |
Power Save Mode | Support U-APSD |
Pre-Authentication | Compliance with 802.11i & 11x |
PMK Caching | Compliance with 802.11i If wireless client devices has authenticated to an access point, it does not perform a full authentication exchange when client devices roaming between access points |
Multicast to Unicast Conversion | Using the IGMP protocol, an access Point delivers high definition content to a large numberof clients simultaneously |
Management | |
Multiple SSIDs |
BSSID support Support 8 SSIDs |
Guest Network | Isolate each client for avoiding an unnecessary touch, leaking sensitive data, and enhancing Internet security and reliability |
VLAN Tag | Independent VLAN setting can be enable or disable. Any packet that enters the Device without a VLAN tag will have a VLAN tag inserted with a PVID (Ethernet Port VID) |
VLAN Pass-through | Broadcast VLAN-tag packets to find the destination and deliver packets over the defined path. The functions allows network topology scalable and flexible |
VLAN Per SSID | Integrate VLAN ID with a SSID interface to forward packets over the defined path. The functions isolate client devices to get more security |
Management VLAN | Feature is enabled with specified VLAN ID, the device will only allow management access with the same specified VLAN ID from remotely location by using protocols such as telnet, SSH, snmp, syslog etc |
Traffic Shaping | Controls the bottle of bandwidth to offer the limited bandwidth for an individual SSID or each client per Access Point |
MAC Address Filtering | Filter up to 32 sets MAC addresses per SSID |
E-Mail Alert | Provides a network monitoring tool for administrators to stay informed the configuration change |
Save Configuration as Users Default | Save the customized configuration as default value for different customer demands |
Wi-Fi Scheduler |
Perform a regular reboot on access point at assigned schedule Perform it to enable or disable 2.4GHz or 5GHz interface from a period time |
SNMP & MIB & CLI |
v1/v2c/v3 support MIB I/II, Private MIB CLI Supported |
RADIUS Accounting | Help operators to offload 3G to Wi-Fi seamlessly |
Wireless Clients List | Provide the list to display real status of wireless client devices on this Access Point |
Security | |
Wireless Encryption Standard | WEP Encryption (64/128/152-bit) |
Hide SSID in beacons | Yes, Supported |
Client Isolation | Block/Isolate the communication between the associated clients under the same WLAN |
HTTPS | A secure communication protocol can be enabled to allow secure management web access over a computer network |
SSH Tunnel | A secure communication protocol can be enabled to allow secure remote shell access or command execution |
Mounting | |
Pole Mounting | Assemble a mounting bracket to fix this Access Point on a pole |
Wall Mounting | Mount this Access Point on a flat wall |
Mechanical & Environment | |
Dimensions (Device only) | 190mm (D) x 38mm (H) |
Weight | 460g |
Operating |
Temperature: -20°C~60°C (-4°F~140°F) Humidity: 0%~90% typical |
Storage |
Temperature: -30°C~80°C (-22°F~176°F) Humidity: 0%~90% typical |
Environment Protection Level | IP55 |
Surge Protection |
Line to Line: 1KV Ling to Ground: 2KV |
ESD Protection |
Contact: 4KV Air: 8KV |
Compliance Regulatory | |
FCC |
Subpart15 B Subpart C 15.247 Subpart E 15.407 |
CE |
EN 301 893 EN 50385 EN 60601-1-1 EN 60601-1-2 EN 55032 EN 55024 |
RCM |
AS/NZS 4268 AS/NZS 2772.2 CISPR 22 |
R&TTE Directive 1995/5/EC | Yes |
CB |
IEC 60950-1 IEC 60950-22 |
S-Mark | UL 60950-1 |
Quick Comparision: EnStationAC vs. EnStation5-AC
EnStationAC | EnStation5-AC | |
---|---|---|
Standards | 802.11ac Wave 1 and a/n | 802.11ac Wave2 and a/n |
Frequency |
5150MHz~5850MHz Note: The supported channels and maximum TX power will vary, depending on local regulations. |
5150MHz~5850MHz Note: The supported channels and maximum TX power will vary, depending on local regulations. |
TX Power | 26dBm | 23dBm |
Data Rates | 867 Mbps | 867 Mbps |
Antennas | Directional 19dBi | Directional 19dBi |
Physical Interface |
1 x Gigabit 802.3af/at Input LAN Port 1 x Gigabit 802.3af PSE Output LAN Port |
1 x Gigabit 24V PoE Input LAN Port 1 x Gigabit Data LAN Port |
Radio Chains/Streams | 2X2: 2 | 2x2: 2 |
Downloads
How & Where to Buy?
To buy the EnStationAC Outdoor Long Range CPE, you can drop by our store (requires prior appointment) located at Novatel Communications, 12 Main St, Buttevant, Co. Cork, P51 K066, Ireland.
To order online, simply click on the Add to Cart button, and then go through the fast, easy and secure checkout process. Payment is provided for your convenience via Authipay Payment Gateway. You can use any supported (MasterCard, Visa, American Express, Diners, etc).
How Will My Order Be Delivered?
Your order(s) will be shipped via express delivery and are normally delivered within 1-4 business days. Your order will be dispatched directly from our warehouse and you will be provided a tracking information for your order, after it is dispatched. If you have any questions on your order status, please contact us.